DANFOSS VLT 6011 PDF

Danfoss Drives regarding PELV .. acteristics of the installation, since Danfoss VLT Max. motor cable length, screened cable VLT V. Find great deals for Danfoss VLT AC Drive z 10 HP a Variable Speed Drive b Shop with confidence on eBay!. Find great deals for Danfoss VLT AC Drive Z 10hp. Shop with confidence on eBay!.

Author: Tetaxe Grolkis
Country: Pakistan
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 28 February 2007
Pages: 98
PDF File Size: 9.50 Mb
ePub File Size: 18.30 Mb
ISBN: 989-2-43846-941-9
Downloads: 89887
Price: Free* [*Free Regsitration Required]
Uploader: Nikozuru

All control In general, electrical noise can be divided into two forms: This display mode is shown when the drive is in Display Mode II and the This display mode is available when local reference is selected. This parameter makes it possible to see the reason why a fault trip occurs.

Danfoss VLT AC Drive z 10 HP a Variable Speed Drive b | eBay

DC link voltage [V] is the drive DC bus voltage. It shows that the drive is in auto mode, with remote reference, and that the motor is Data Item: All drives except VLTto V and VLTThe shield of the control wires must be grounded at the cable clamp at to V must be mounted directly to the wall with no spacers. During closed loop operation, there are three ways to use the PID 1 Setpoint and 2 Feedbacks controller and setpoint and feedback signals: After programming, the drive will, in many in the parameter sections of this manual.

The unit for the reference can be seen from the following table: Warnings And Alarms Warnings and Alarms In addition, an automatic reset may be selected in parameterReset Function which will reset all non-trip lock faults.

  CPH DOX PROGRAM PDF

Danfoss VLT 6002-6011 Installation, Operation And Maintenance Manual

General 25 inches mm front space for access. The table below gives the operating data options for the first and Line 4 is the status line and the information is automatically generated second lines of the display.

This parameter chooses the active resulting reference. The drive is attempting to avoid a trip from overvoltage by extending its decel ramp Status messages appear in the fourth line of the display as shown time.

Don’t show me this message again. Page 90 Fault Log: Display Keys for changing the display All terminals for the low voltage control wires are located under the Many of 0611 terminals have multiple functions 60111 by protective cover below the keypad.

Danfoss VLT 6011 AC Drive 175Z7360 10hp

Set the required value for maximum output frequency. The built-in proportional, integral, vlh PID controller in the drive maintains a constant condition pressure, dafoss, flow, etc. The table below shows when the motor is running forward and reverse when Digital input, Serial communication, Logic and or Logic or has been selected. The calculation is based on the mean value in kWh over one hour. The frozen reference is saved after a stop command and when power is removed.

The pulse rate is set by parameterTerminal 45, Output, Pulse Scaling.

Input And Outputs – Parameters Through Inputs and Outputs Parameters through In this parameter group, the functions of the drive input 601 output terminals are defined. The drive will continue to Turn off the drive and check for free rotation of the motor shaft and function, but is likely to fail at the next power-up. Reference Handling Reference Handling It is possible to have both internal preset references and external references at the same time.

  MAGPUL PDR PDF

For a read command, the index must have the following format: If the multiple motors are of significantly different sizes, starting problems High Voltage Form C Relay may occur.

Relay Outputs Relay Outputs Relay outputs 1 and 2 can be used to give danflss present status or a warning.

Page 99 AMA has been interrupted by the user. Reference Type Reference Type The example below shows how the resulting reference is calculated when Preset references danfosx used together with Sum and Relative references set in parameterReference Type. See also parameters throughDisplay Terminal 54, Analog Input [V], parametergives the voltage value Readout.

Bit 03, Coasting Stop: Enter text from picture: Page 43 Description of choice: Check alarms section in this manual for possible causes of alarm. HIGH reply Error message The parameter number used does not exist There is no write access to the 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 Contact the Danfoss other causes of the overload.

Posted in Art